Hi!

This is my first post here, but i think this is the right way to present my self My friend rbagoros show me that board and i like it very much at the moment!
I´m not a stunter, but i´m looking forward to do something about this 2 years ago i bought a yamaha bw´s and modified it, so it became quite fast... here some photos:








Take care,
ali




The final setup looked something like that:

-Stage6 HPC
-Stage6 racing drive face
-Stage6 primary transmision
-Hebo AC racing cylinder (pimped by me)
-Hebo BigValve kit (pimped by me)
-Malossi Delta Clutch
-Malossi CDI TC-Unit RPM
-Hebo NG competition kit vario
-BGM Wing Bell
-Doppler Venturi AirFilter
-SKF C4 bearing
-Sinter racing brake pads
-stage6 boost botle
-Denso W24FS-ZU
-DellOrto 21"
-Tehnigas RS70 chromed

Few months ago we puted the engine on a minibike frame.... i must say this is a prety wild thing






That mens that my yamaha has no engine at the moment and here is the part were my "scooter dreams" are going to come true

So i bought a piaggio 180ccm, 2 stroke engine from gilera runner. Stock it has nearly 20hp, but it is going to be modified




Until today i took the engine apart and clean it well. At the moment i´m waiting for some engine parts and next week the scooter shold run (that are only the plans). Here some more pics:

The cooling system will consist of 2 runner 50 radiators with 12cm Papst fans:



Cylinder:



Stage 6 PWK 24:



Block:



[strike]

Next week i (and a mechanic-friend of mine) will try to fix the engine and the cooling system to the frame.... sure there will be some problems, but it should work

The setup will be:

Malossi MHR zylinder-head
Malossi MHR vario
Malossi Kevlar belt
LeoVinci ZX 180
PWK 24
Stage6 aspiration mouth
Stage6 280mm floatnig disc
Koso Turbine air filter
...and other stuff

And here one more photo of bw´s waiting for new engine




I´m also thinking about 12o´clock but first the scooter schould run "normaly". Coments are welcome

8.2.2007



Until i´m waiting for other parts, there are things like cleaning, painting, etc. to do. So today i painted the ventilators, rear shock absorber and the plastic which comes over the magnet. Here my favourite parts...ready to go:P


9.2.2007




I got two packages today..... i can´t stop looking at the parts The one are the parts from SC:
-Malossi MHR vario
-Malossi zylinderhead
-Malossi kevlar belt
-Malossi Clutch springs
-small stuff like-transmission oil, exhaust seal, "kickstarterrietzel", etc.







The other one is used oversize disc stage6 280mm... it is like new... used only few km.




I´m still waiting for some piaggio original parts like oil/water-pump belt, piston rings and the parts from SA... aspiration mouth and Koso Turbine air filter. Next week the project will really start


13.2.2007








Today we put the shock absorbers from beta to my original cross, wich we had to modify. Shock absorbers also had to be changed, because of the rim from gilera.
I also made a spacer for the oversize disc so the gripper is in optimal position.
Tomorow we will try to put the gilera and yamaha frame together. I´m also thinking about some frame-reinforcements, because now it looks like a bicycle.

14.2.2007

Today i didn´t have many time, so i made only some fine adjustmens on the front braking system (new pads-sinter racing, etc.). Here the final photo of the front :



Tomorow we will veld the frame together....here what i did today (cut some steel away):




And here the parts ready to go:



I also polished the exhaust chanel of cylinder:



It was valentin`s day so i was with my girlfriend.... unbelivable but there are still some things more important then scooter


17.2.2007

Last two days we were working (and drinking ) real hard . He re some pics what we did in two days:



Dani and Reni helping me



Me... measuring again



Ready to go...



Final test before painting:



And reni doing his best



Yesterday i brought the parts back home...



....and started put things together....





Still a lot of things (modifications) to do, especially the body parts (plastics).

19.2.2007

Here what i did today... tomorow i´m going to bratislava until friday. Then the project will go forward again











24.2.2007

On friday i got some parts from SA and from italy. The PWk had to be modified so now it fits perfectly. I also got the zx 180... here some pics












26.2.2007

Today i got the piston rings and so i put the engine together....also the exhaust. Here some pics:










28.2.2007

I have to learn a lot this time, so i work only at small things like electrics, etc. I got the air intake cover for vario by typhoon 125 (fits perfectly), so i don´t need so long to take the engine cover down. I also got SST shirt from "my bitch" Rocket..... nice job









1.3.2007

Today i mounted the engine on the frame, boost botle, cooling fans and continued on the electrics. Here some pics:







On sunday it should run

3.3.2007

My friend dani helped me by finishing electrics and i mounted the fluid box from beta...it fits very nice, so there are no probblems with plastics. And then we started the engine..... it started after the 3rd shot!! I didn´t drive it, because there is no holder for the rear shock absorber ( should be done yesterday, but i was to late to buy some steel for it). Here a short movie (klick on the movie icon):








5.3.2007

I prepaired the rims for painting adn today we will veld the holder for the rear shock absorber. Here two pics of how it looks lat the moment:






I also ordered Dhl... hope it will arrive this week

8.3.2007

The holder for the rear shock absorber is done and the rims are painted....






10.3.2007

Jo!

The rims are finished.... time to put everything together and then....gaaaassssss Pics:





In real the colour is totally different (more agressive )...

.... few hours later


I put the rims on, checked the screws and drove few km with the scooter... All i can say: this is sick

It goes like a hell.... now i see how 20+PS on a bw´s is like..... I can´t describe it, because the feeling is just fuc*** great At the moment, driving is pretty dangerous: too high at the back and no front brake (have to buy the pipe). Video coming soon, here some pics before and after the testdrive:










12.3.2007

Some new photos and stuff. New parts:
-str8 dhl gold-orange
-str8 adapter carbon
-SA pad













28.5.2007


Back again! Sorry because i wasn´t posting anymore, but i had no time and there is another projekt happening at the moment (4 wheels/1000kg/200ps+) Here some photos from the last two months.... hope you like it. Movie is comming, when i change some bearings.... but the escooter is running and goes like hell So here the pics:


























Take care,
ali

Yeah thats my homie Keep up that good work

this will look sick...hope you manage it...i wanna see it how it looks

Nice yob...do you have a movie, maybe, from the time when your Bw's had that setup?

Very nice.. i love tuned engine swamps... keep us informed =))

----

p.s. please read the rules for this project forum

zerocool wrote (View Post): › Nice yob...do you have a movie, maybe, from the time when your Bw's had that setup?

There are some movie clips, but rather bad. Don´t worry, certainly there will be a long video of minibike with the bw´s engine and bw´s 180, when everything is ready to go

yours,
ali

PS: sorry..... now i know the rules

Pretty sick man

damn you are good! i expect some other pictures next week when i come back from rome

robbii2031 wrote (View Post): › damn you are good! i expect some other pictures next week when i come back from rome

Thank you Sure there will be some pictures..... until sunday the engine should run, because then i´m going to bratislava for one week

Have a nice time in rome.... one of my favourite citys The girls are just

yup.. thats it.... pimp project... just keep it commin...

the disc looks awsome...i love oversizes

Very nice yob 4 now...keep it that.

great job guys i really like it, but i think you made mistakes about exhausts on booth engines, for bw's setup that technigas rs70 is not enough, and for 180 engine i heard that zx180 is not too good maybe even worse than stock, but everything else is great just keep the good work;)

and i believe that minibike is going like hell is it possible to stop it normaly

.:vulin:. wrote (View Post): › great job guys i really like it, but i think you made mistakes about exhausts on booth engines, for bw's setup that technigas rs70 is not enough, and for 180 engine i heard that zx180 is not too good maybe even worse than stock, but everything else is great just keep the good work;) and i believe that minibike is going like hell is it possible to stop it normaly

You are right....the rs70 was never enought but it works god. For this engine i had no exhaust and the price difference between zx 180 and stock was less then 30€ ... that´s why i bought the zx (better quality and look ).

PS: it´s not possible to stop it normaly

Very nice project.I'll also put some piaggio engine to my derbi,but it would be 125 and this photos will sure help me